Absolute Pest Solution

• Nitotile Gpx Is A High Quality Adhesive For The Permanent Fixing Of Ceramic  And Vitrified Tiles For Both Internal & External Applica-tion Of Tiles  For Wet Area, Dry Area & Submerged Conditions.  It Can Also Be Used For Fixing Of Insulating And Acoustic Boards Based On Expanded Polystyrene Etc. Typical Uses Include :   Wet Areas - Kitchens And  Bathrooms  Tile Claddings Swimming Pools Fixing Of Ceramic And Vitrified Tiles For  Floor & Wall (Both          
• Internal & External Application)advantages Tropical Grade To Suit Indian Working Conditions good Open Wet Time good Slip Resistance high Adhesion Strength water Proof Good Slip Resistance   Can Be Used In Totally Submerged Conditionsstandards Compliancenitotile Gpx Confirms To Is 15477 Type  I & Ii. Descriptionnitotile Gpx Cementitious Powder Is Available In Grey Colour.propertiesspecific Gravity : 1.18 To 1.19 G/cctechnical Supportfosroc  Offers  A  Comprehensive  Technical  Support  Service  To  Specifiers, End Users And Contractors. It Is Also Able To Offer On-site Technical Assistance, An Autocad Facility And Dedicated Specification Assistance In Locations All Over The World.instructions For Usesurface Preparationall Surfaces Must Be Sound And Thoroughly Clean Before Nitotile Gpx Is Applied.  All Traces Of Grease Or Oil Must Be Removed With A Chemical Degreaser.  All Loose Particles Of Mortar, Old Wallpaper, Paint Etc. Must Be Physically Removed.       Nitotile Gpxsurfacesnitotile Gpx Can Be Applied Directly On Concrete, Cement Screeds, And Cement Or Lime Mortar.  Special Attention Must Be Given To New Construction Prior To Commencing Tiling.  Tiles Should Not Be Placed On Concrete Or Brickwork Until All Shrink-age Movement Has Taken Place.to Use Nitotile Gpx On Gypsum Or Gypsum Board Substrates, Diluted Nitobond Ar (1 : 3 With Water) Should Be Applied  To The Surface Of The Gypsum Or Gypsum Board  Prior To Application Of Nitotile Gpx.mixingnitotile Gpx Should Be Mixed With Clear Potable Water In The Ratio 4:1 By Weight (4 Part Powder : 1 Part Water).  A Slow Speed Drill Fitted With A Mixing Paddle  Is Recommended For Mixing.  Add Powder To Water And Mix Until A Uniform, Lump-free Consistency Is Achieved. The Total Quantitiy Of Water May Be Slightly Adjusted To Achieve The Required Consistency.applicationnitotile Gpx Should Be  Spread On The Substrate To A Uniform Thickness Of 2-3mm, And Then Combed Horizontally With A Ser-rated Trowel.place Tiles Firmly Into Adhesive Bed, Ensuring Good Contact With A Twisting Motion.  Only Apply To Areas Which Can Be Tiled In The Adhesive’s Open Wet Time (Up To 1m2 At A Time).jointsit Is Recommended That When Fixing Ceramic Tiles, A Minimum Spacing Of 2mm Be Left Around Each Tile.finishingremove Excess Adhesive With A Damp Cloth Before Material Has Set.  Joint Grouting With Nitotile Grout*† May Be Commenced 24 Hours After Tiles Have Been Laid.cleaningnitotile Gpx Should Be Removed From Tools, Equipment And Mixers With Clean Water Immediately After Use.  Cured Material Can Only Be Removed Mechanically.limitationsnitotile Gpx Should Not Be Used When The Temperature Is Below 5°c And Falling.  The Product Should Not Be Exposed To Moving Water During Application.  If Any Doubt Arise Concerning Tempera-ture Or Substrate Conditions, Consult Your Local Fosroc Office.

• BiotileAdhesive for fixing ceramic tiles indoor and outdoor areas.
• Walls and floors
• Adjustable
• No sag

Highly flexible, multipurpose, structural adhesive to fix fully vitrified tiles and natural stone of all types and size.

• Water resistant
• Sustains heat ageing
• No shrinkage