Absolute Pest Solution

Conplast WL Xtra is a dark brown liquid based on cement dispersion polymers which mixes readily with water and therefore disperses evenly. Conplast WL Xtra waterproofs by improving the quality of the concrete or mortar. It reduces the water demand for required workability and minimises segregation and bleeding. Thus it is more effi cient compared to traditional powder and conventional integral waterproofi ng compounds as its use results in two fold improvement of concrete or mortar. 

Fosroc Brushbond
Uses To protect atmospherically exposed reinforced concretestructures from attack by acid gases, chloride ions, oxygen,water and water vapour and can be used to produce vapourbarriers . The product is also recommended to protect othercementitious substrates and masonry for new and existingstructures. Typical applications include  Re-facing and reprofiling concrete & masonry surfaces Flexible coating to bridge shrinkage cracks Waterproof coating for water tanks and reservoirs Vapour barriers Robust coating which can withstand light pedestriantraffic Backing to marble and granite, preventing water ingressand alleviate stainingAdvantages Excellent barrier to carbon dioxide, chloride ions andwater Allows water vapour to escape from the structure Water proof - suitable for water retaining structures High resistance to the effects of long-term weathering,durable in all climatic conditions including UV attack Minimum surface preparation needed and low labourcosts Flexible, with thermal expansion similar to concrete Covers honeycombed and pitted poured concreteeffectivelyDescriptionBrushbond comprises a two component acrylic polymermodified cementitious coating supplied in ready to mix kits.Brushbond can be simply applied by stiff brush, roller, sprayor trowel to obtain the desired texture.Note : For potable water applications, please refer toNitocote CM210 and Brushbond FLX lll datasheetsDesign criteriaThe coating should be applied in two coats to achieve a totaldry film thickness of not less than 2mm. Areas subjected tolight foot traffic should receive minimum 2mm thickness andan additional 2mm coating should be applied to areas ofmoderate to heavy pedestrian conditions. To achieve thecorrect protective properties, Brushbond must be applied onto the substrate at the coverage rates recommended.

Main Uses:

• Suitable for sealing water tanks,reserviors,toilets and bathrooms,balconies and basements as well as filling blowholes,cracks,imperfections and for providing concrete surfaces with a uniform appearance.

Advantages:

• Minimum surface preparation needed
• Excellent adhension.Bonds directly to porous and non- porous surfaces
• Waterproof and non-toxic-Ideal for potable water tanks
• Excellent for damp-proofing basements below ground
• Breathable-Allows transmission of water vapour from interior of building
• High resistance to carbon dioxide and chloride ion diffusion
• Can fill the honeycomds, dot surfaces and concrete with potholes

Description:

• Brushbond comprises a two component acrylic polymermodified cementitious coating supplied in ready to mix kits.Brushbond can be simply applied by stiff brush, roller, sprayor trowel to obtain the desired texture

Note: For potable water applications, please refer toNitocote CM210 and Brushbond FLX lll datasheets


Acrylic polymer modified protective/decorative coating:

• The protective coating shall comprise specially selectedcements, graded hardwearing aggregates and additivessupplied in powder form together with a liquid component ofblended acrylic co-polymers and wetting agents. The total dryfilm thickness of the coating shall be not less than 2 mm andshall be capable of providing resistance to wear and weatherand good chemical resistance to mild inorganic acid solution,diesel oil, gasoline, chlorides, de-icing salts, effluents andorganic solvents

Instructions for Use:

Preparation:

• All surfaces should be dry and free from contamination suchas oil, grease, loose particles, decayed matter, laitance, andall traces of mould release oils and curing compounds. Thisis best achieved by lightly grit-blasting the surface.
• Where moss, algae or similar growths have occurred,treatment with a proprietary biocide should be carried out afterthe grit-blasting process
• Spalled and deeply disintegrated concrete should be removedto sound concrete and repaired with a Fosroc repair system.For further advice, consult the local Fosroc office.
• It is essential that all surfaces to be treated be pre-soakedwith clean water prior to application of Brushbond

Mixing:

• Brushbond liquid should be poured from the plastic containerinto the metal drum provided. For brush application consistencymix with a slow speed drill (500 r.p.m.) fitted with a FosrocMixing Paddle (MR3)
• The powder component should be added gradually to the liquidto avoid lump formation and mixed for 2 to 4 minutes.
• Brushbond should be immediately used after mixing. Do notmix more material than can be used within the pot life. Keepmixing Brushbond during the application.

Application:
Application of Brushbond on hot substrates (i.e. over 40oCsurface temperature) will need the prior application of a primercoat. Mix Brushbond and water in slurry like consistency andapply Brushbond over the primer whilst it is still wet.

For best results, surfaces should be damp. In order to obtainthe protective properties of Brushbond, it is important that thecorrect rates of application are observed.
Use a short stiff brush (preferably 120 - 200mm width) andapply in one or two coats as required.

 Other Details:

• Cementitious acrylic waterproof coating

Hydroproof Xtra is formulated to be mixed with cement on site or simply brush applied over concrete or masonry surfaces to provide an eff ective waterproof membrane.

SikaTop® Seal-107 IN is a two part acrylic polymer modified cementitious liquid applied waterproofing coating system. It comprises of a liquid polymer and a cement based mix incorporating special admixtures. It is applied to concrete and mortar to prevent water infiltration. USES Interior and exterior waterproofing and damp-proofing of concrete, cementitious rendering, brickwork and blockwork ??? Protection of concrete structures against the effects of de-icing salts and freeze-thaw attack ??? Exterior waterproofing of basement walls in new construction and refurbishment ??? ??? Pore / blowhole filling Rigid waterproofing of water tanks, bathrooms, toilets, etc. ??? Sealing fine “hairline” cracks in concrete structures not subject to movement ??? ??? Sealing internal basement walls against dampness ??? Levelling mortar for concrete repair works
Easy to apply by brush or in thin trowel applications ??? No additional water is required to make the slurry ??? Pre batched components with consistent quality ??? Hand or Spray applied ??? Easy and fast mixing ??? Increased frost and salt resistance Very good adhesion with sound and prepared substrates ??? Protects concrete against water penetration, chloride and carbonation ??? ??? Non Corrosive to steel and iron ??? Approved for potable water contact ??? Flexible enough to bridge hairline crack ??? Bonds well to all damp substrates Can be applied on reinforced concrete, mortar or masonary

Elastomeric cementitious coating. Uses Nitocote CM210 is an elastomeric cementitious coating, used for waterproofi ng water retaining structures and water excluding structures. Nitocote CM210 provides an elastomeric waterproof coating suitable for use in potable water tanks, reservoirs, canals and culverts. The material which can be used on concrete, brick and blockwork substrates exhibits good crack bridging qualities even after long term water immersion. This is a conditions a number of cementitious coatings cannot satisfy. Nitocote CM210 has been developed to readily accommodate the maximum permissible crack widths recommended in BS8007:1987 the British Standard Code of Practice for the design of concrete structures for retaining aqueous liquids. Advantages  Approved for use in contact with potable water.  Withstands high positive and negative hydrostatic pressures  Excellent crack accommodation after immersion.  Excellent bond to concrete and masonry.  Long working life.  Easy application by brush, roller, trowel or spray.  Bonds to green or damp concrete.  Eff ective barrier to sulphates and chlorides. Standards compliance  Nitocote CM210 meets the requirements of BS 6920, WRAS. approved for use in contact with potable water up to 50ºC.  DIN 1048 : Water Penetration Test.  Fire Tested to BS476 : 1987 Parts 6 and 7. Description Nitocote CM210 two-component polymer modifi ed cementitious coating is supplied in pre-packaged form. The product is designed to be easily mixed on site using a slow speed drill fi tted with a mixing paddle and then applied to the substrate using either brush, trowel or spray. Roller application may also be used, however, fi nishing the surface with a trowel is recommended for best results. Nitocote CM210, available in grey and white, cures to form and elastomeric impermeable membrane Technical support Fosroc off ers a comprehensive range of high performance, high quality repair, maintenance and construction products. In addition, Fosroc off ers a technical support package to specifi ers, end users and contractors, as well as on-site technical assistance in locations all over the world.

Usage

• Waterproofing of roof slab, sunken slabs, basements, water tanks, sunshades etc.
• As a bonding agent for uses in repair and plastering
• For making polymer mortar for repairs mortars etc.
• For treatment for leaching and salt petre action
• As a multipurpose mortar admixture for injection grouts
• Additives to cement based paints for waterproofing

 Advantages

• Improved impermeability against water ingress   
• Extremely good bonding to moist substrates, extremely improved mechanical, flexural strength and abrasion resistance properties
• UV resistant & suitable for external coating
• When used as an additive to cement based paint improves impermeability, water repellence and anti fungal property of the painted surface (site trials are always advised before application for shade variations, if any)
• Sika® RainTite I can be diluted with water (1 : Nil to 1 : 4) depending on the type of application
• Screed required with Sikacim®/ Sika® Plastocrete Super to protect waterproofing layer

Packaging

 

250g, 500g, 1kg, 5kg, 10kg, 20 kg and 200kg.

Colour

 

Milky white liquid

Rapid foaming and setting resin for stopping fl ow of water Uses for Stops the flow of water when injected into cracks in concrete in the presence of moving water. Nitofi ll WS60 with Nitofi ll UR63 provides an eff ective system for crack sealing in wet conditions.

Additional Information:

• Production Capacity: ACCORDING TO DEMAND
• Delivery Time: 1-2 DAYS
• Packaging Details: PP BAGS

Main uses

• Ensure even concrete surface
• Reduces opportunity of damage to formwork, extending usable life.
• Minimises cleaning of formwork before re-use
• Suitable for use with virtually all types of formwork.
• Inhibits corrosion of steel formwork.

Sika® RainTite I is a multifunctional polymer emulsion for enhancing the properties of mortar/concrete/grout/cement slurry. It provides a good adhesion, water resistance and improvement of several other properties

Auracast 50 is a unique combination of the latest generation super plasticisers, based on polycarboxylic ether polymer with long side chains and short main chains. This greatly improves cement dispersion and as well as facilitate quick start of hydration process. At the start of the mixing process an electrostatic dispersion occurs but the cement particles capacity to separate and disperse. This mechanism considerably reduces the water demand in fl owable concrete.

ARDA Roof Guard White is a specialacrylic resin based, single part flexible,t h i x o t r o p i c w a t e r p r o o f c u mdecorative coating. It is economical andideal for use in vertical/ horizontalsurfaces. Suitable for painting externalwall as it offers both water proofingand decoration. Can also be used as abase & intermediate coat in brick bat coba or IPS flooring.

Additional Information:

• Delivery Time: 5-7 days after order confirm

Hydroproof Single Component Acrylic Polymer For CementBased Waterproof Composite CoatingMembraneUsesProvides An Eff Ective And Economical Method Of Waterproofi NgTo Concrete And Masonry Surfaces, By Mixing With Cement AndApplication By Brush.AdvantagesNon - Toxic, Non-fl Ammable And User FriendlyProvides A Tough, Impermeable Waterproof MembraneCan Be Applied By Brush, On Horizontal And Vertical SurfacesExcellent Adhesion To Concrete And Masonry SurfacesProtects Concrete And Mortar From Natural Elements SuchAs Wind, Rain, Sunlight breathable - Allows Inside Water Vapour To EscapeDescriptionHydroproof Xtra Is Formulated To Be Mixed With Cement On SiteOr Simply Brush Applied Over Concrete Or Masonry Surfaces ToProvide An Eff Ective Waterproof Membrane.Technical SupportFosroc Provides A Technical Advisory Service Supported By ATeam Of Specialists In The Fi Eld.Areas Of ApplicationBelow Sloping Screed Or Waterproof Plaster On :Roofs, Terraces And Balconies As A Sandwich LayerPools And FountainsReservoirs And ChannelsEnd Walls Subjected To Rain

Nitocote CM210 two-component polymer modifi ed cementitious coating is supplied in pre-packaged form. The product is designed to be easily mixed on site using a slow speed drill fi tted with a mixing paddle and then applied to the substrate using either brush, trowel or spray. Roller application may also be used, however, fi nishing the surface with a trowel is recommended for best results. Nitocote CM210, available in grey and white, cures to form and elastomeric impermeable membrane

Nitobond EP Std is a two component epoxy bonding agent supplied in pre-weighed quantities for ready on-site mixing and use.

Conbextra GP2(N) is supplied as a ready to use dry powder. The addition of a controlled amount of clean water produces a free flowing, non-shrink grout for gap thicknesses up to 100mm. Conbextra GP2(N) is a blend of Portland cement, graded fillers and chemical additives which impart controlled expansion in the plastic state whilst minimising water demand. The low water demand ensures high early strength. The graded fi llers are designed to assist uniform mixing and produce a consistent grout. 

Additional Information:

• Packaging Details: 30 Kg bag